Type
Crochet
Difficulty
beginner
Category
amigurumi
AI Thinking Process
Planning
Verification
Pattern
Honey Bear (Disney-Style) Amigurumi
Beginner Simple-Shapes Pattern
A cuddly 5Β½β6 inch (14β15 cm) honey-loving bear worked entirely from basic spheres, ovals and cylinders. Perfect first character project.
Materials
- Worsted weight (4) yarn:
- Main color (MC): golden yellow or honey gold β approx. 60 yd (55 m)
- Contrast color (CC): bright red β approx. 20 yd (18 m)
- Small amount black for embroidery (or black safety eyes 6β8 mm)
- Optional: tiny scrap brown for honey-pot accent
- US E-4 (3.5 mm) crochet hook (or size needed to obtain firm fabric)
- Polyester fiberfill stuffing
- Yarn needle
- Stitch marker
- Scissors
- Optional: 6β8 mm safety eyes, black embroidery floss
Abbreviations (US Terms)
- ch: chain
- sc: single crochet
- inc: increase (2 sc in same stitch)
- dec: invisible decrease (sc2tog)
- st(s): stitch(es)
- rnd(s): round(s)
- MR: magic ring
- FO: fasten off
- [ ]: total stitch count at end of round
Gauge
5 sc Γ 5 rnds = 1" (2.5 cm) in continuous sc worked tightly.
Exact gauge is less critical than a firm fabric that hides stuffing. Go down a hook size if stitches look loose.
Finished Size
Approximately 5Β½β6" (14β15 cm) tall when made with worsted yarn and E-4 hook.
Notes
- Work in continuous spirals unless stated. Do not join rounds; mark the first st of each rnd with a stitch marker.
- Stuff firmly as you goβespecially the head and bodyβso the bear holds its shape.
- Use the invisible decrease for a smooth surface.
- Color changes: work the last yarn-over of the previous stitch in the new color.
- All pieces are made separately and sewn together.
Pattern Pieces
Head (sphere β make 1 in MC)
Rnd 1: 6 sc in MR. [6]
Rnd 2: inc in each st around. [12]
Rnd 3: (sc, inc) around. [18]
Rnd 4: (2 sc, inc) around. [24]
Rnds 5β9: sc around. [24] (5 plain rounds)
Insert safety eyes between Rnds 6β7, about 5β6 sts apart, or embroider later.
Rnd 10: (2 sc, dec) around. [18]
Stuff head firmly.
Rnd 11: (sc, dec) around. [12]
Rnd 12: dec around. [6]
FO, leaving a 8" tail. Thread tail through remaining 6 sts and pull closed. Weave in end.
Snout (small half-sphere β make 1 in MC)
Rnd 1: 6 sc in MR. [6]
Rnd 2: inc in each st. [12]
Rnd 3: sc around. [12]
FO, leaving long tail for sewing. Lightly stuff. Embroider a small black nose and straight-line mouth on the snout before attaching.
Ears (make 2 in MC)
Rnd 1: 6 sc in MR. [6]
Rnd 2: (sc, inc) around. [9]
Rnd 3: sc around. [9]
FO, leaving long tail. Do not stuff (or stuff very lightly). Flatten into a semi-circle.
Body (oval β make 1, starting in MC)
Rnd 1: 6 sc in MR. [6]
Rnd 2: inc in each st. [12]
Rnd 3: (sc, inc) around. [18]
Rnd 4: (2 sc, inc) around. [24]
Rnds 5β6: sc around. [24]
Change to CC (red shirt).
Rnds 7β10: sc around. [24] (4 rounds of red)
Change back to MC.
Rnds 11β12: sc around. [24]
Rnd 13: (2 sc, dec) around. [18]
Stuff body firmly, keeping the bottom flat-ish.
Rnd 14: (sc, dec) around. [12]
Rnd 15: dec around. [6]
FO, close hole, weave in end.
Arms (cylinder β make 2 in MC)
Rnd 1: 6 sc in MR. [6]
Rnd 2: (sc, inc) around. [9]
Rnds 3β7: sc around. [9]
Lightly stuff.
FO, leaving long tail for sewing. Flatten open end.
Legs (cylinder β make 2 in MC)
Rnd 1: 6 sc in MR. [6]
Rnd 2: inc in each st. [12]
Rnds 3β4: sc around. [12]
Rnd 5: (2 sc, dec) around. [9]
Rnds 6β7: sc around. [9]
Stuff firmly.
FO, leaving long tail. Flatten open end.
Optional Tiny Honey Pot (simple cylinder β brown scrap)
Rnd 1: 6 sc in MR. [6]
Rnd 2: (sc, inc) around. [9]
Rnds 3β4: sc around. [9]
FO, stuff lightly, sew closed or leave open as a little βpot.β Embroider a tiny βHUNNYβ if desired.
Assembly
- Snout: Center snout on lower half of head (covering roughly Rnds 7β10). Sew securely with MC tail. Embroider nose and smile with black yarn if not done earlier.
- Ears: Pin ears to sides of head at Rnds 3β5, slightly toward the back. Sew along the curved edge.
- Head to Body: Sew head centered on top of body (red shirt uppermost). Use plenty of stitches so the neck is stable.
- Arms: Attach arms at the sides of the body, just below the color-change line of the red shirt (approx. Rnd 7β8 of body). Angle slightly forward.
- Legs: Attach legs to the bottom front of the body so the bear can sit. Space them about 4β5 sts apart.
- Optional honey pot: Sew to one paw or leave loose as a play accessory.
- Weave in all remaining ends securely.
Finishing Touches
- Embroider two small black eyebrows above the eyes for classic Pooh expression.
- Add a tiny bit of blush (pink yarn or fabric marker) on cheeks if desired.
- Shape by rolling the pieces between your hands.
- For a keychain version, scale down by stopping head/body increases at 18 sts and use DK yarn.
Care
Surface wash with cool water and mild soap; air dry. Do not machine wash.
Enjoy your honey bear! He is ready for adventures (and imaginary honey).
Disclaimer: This pattern was generated by AI and should be reviewed for accuracy before use. While we strive for quality, AI-generated content may contain errors. Please verify measurements, stitch counts, charts, and instructions before beginning your project. Generated by purlJam.uk
Love this pattern?
Save this pattern to your free PurlJam libraryAccess your pattern anytime
Bookmark this page to access your pattern anytime